Accuracy Definition

In general, refers to precision and/or exactness, but to dig into this term...

In the fields of science, engineering, industry and statistics, accuracy is the degree of conformity of a measured or calculated quantity to its actual (true) value. Accuracy is closely related to precision, also called reproducibility or repeatability, the degree to which further measurements or calculations will show the same or similar results.

The results of calculations or a measurement can be accurate but not precise; precise but not accurate; neither; or both. A result is called valid if it is both accurate and precise.

The related terms in surveying are error (random variability in research) and bias (non-random or directed effects caused by a factor or factors unrelated by the independent variable).

Accuracy vs Precision - The Target Analogy

Accuracy is the degree of veracity while precision is the degree of reproducibility. The analogy used here to explain the difference between accuracy and precision is the target comparison.

In this analogy, repeated measurements are compared to arrows that are fired at a target. Accuracy describes the closeness of arrows to the bullseye at the target center. Arrows that strike closer to the bullseye are considered more accurate. The closer a system's measurements to the accepted value, the more accurate the system is considered to be.

To continue the analogy, if a large number of arrows are fired, precision would be the size of the arrow cluster. (When only one arrow is fired, precision is the size of the cluster one would expect if this were repeated many times under the same conditions.) When all arrows are grouped tightly together, the cluster is considered precise since they all struck close to the same spot, if not necessarily near the bullseye. The measurements are precise, though not necessarily accurate.

However, it is not possible to reliably achieve accuracy in individual measurements without precision — if the arrows are not grouped close to one another, they cannot all be close to the bullseye. (Their average position might be an accurate estimation of the bullseye, but the individual arrows are inaccurate.)

Accuracy and Precision in Logic Level Modeling and IC Simulation

Quantifying Accuracy and Precision

Ideally a measurement device is both accurate and precise, with measurements all close to and tightly clustered around the known value.

The accuracy and precision of a measurement process is usually established by repeatedly measuring some traceable reference standard. Such standards are defined in the International System of Units and maintained by national standards organizations such as the National Institute of Standards and Technology.

Precision is usually characterised in terms of the standard deviation of the measurements, sometimes called the measurement process's standard error. The interval defined by the standard deviation is the 68.3% ("one sigma") confidence interval of the measurements. If enough measurements have been made to accurately estimate the standard deviation of the process, and if the measurement process produces normally distributed errors, then it is likely that 68.3% of the time, the true value of the measured property will lie within one standard deviation, 95.4% of the time it will lie within two standard deviations, and 99.7% of the time it will lie within three standard deviations of the measured value.

This also applies when measurements are repeated and averaged. In that case, the term standard error is properly applied: the precision of the average is equal to the known standard deviation of the process divided by the square root of the number of measurements averaged. Further, the central limit theorem shows that the probability distribution of the averaged measurements will be closer to a normal distribution than that of individual measurements.

With regard to accuracy we can distinguish:

• the difference between the mean of the measurements and the reference value, the bias. Establishing and correcting for bias is necessary for calibration.
• the combined effect of that and precision

A common convention in science and engineering is to express accuracy and/or precision implicitly by means of significant figures. Here, when not explicitly stated, the margin of error is understood to be one-half the value of the last significant place. For instance, a recording of '8430 m' would imply a margin of error of 5 m (the last significant place is the tens place), while '8000 m' would imply a margin of 500 m. To indicate a more accurate measurement that just happens to lie near a round number, one would use scientific notation: '8.000 x 10³ m' indicates a margin of 0.5 m. However, reliance on this convention can lead to false precision errors when accepting data from sources that do not obey it.

Looking at this in another way, a value of 8 would mean that the measurement has been made with a precision of '1' (the measuring instrument was able to measure only up to 1's place) whereas a value of 8.0 (though mathematically equal to 8) would mean that the value at the first decimal place was measured and was found to be zero. (The measuring instrument was able to measure the first decimal place.) The second value is more precise. Neither of the measured values may be accurate (the actual value could be 9.5 but measured inaccurately as 8 in both instances). Thus, accuracy can be said to be the 'correctness' of a measurement, while precision could be identified as the ability to resolve smaller differences.

Precision is sometimes stratified into:

• Repeatability - the variation arising when all efforts are made to keep conditions constant by using the same instrument and operator, and repeating during a short time period; and
• Reproducibility - the variation arising using the same measurement process among different instruments and operators, and over longer time periods.

As stated before, you can be both accurate and precise. For instance, if all your arrows hit the bull's eye of the target, they are all both near the "true value" (accurate) and near one another (precise).

Something to think about: In the NFL, a place kicker makes 9 of 10 field goals, and another makes 6 of 10. Even if the 6 that the second kicker made were straight down the middle and the first kicker just made his in, he is still less accurate and less precise than the first kicker. This differs from the darts example because either you make it or you do not; there are not different levels of points that can be scored.

Know matter if you need to know "what is a Accuracy", the definition of a "Accuracy", or the meaning of a "Accuracy", you can find it here at Network Liquidators. There's quite a bit of information out there to learn, and it all starts by you having the initiative to seek out that information.

About Our Company
Network Liquidators (NWLQ) is in the business of providing their clients with a low cost solution for building and maintaining their network infrastructure. With over 20 years of experience in IT sales, we have the stock and know how to service our worldwide client base. NWLQ sells new sealed, new open box, used and refurbished networking systems. From the largest datacenters and Universities, to small to medium sized businesses, NWLQ is the industry leader.

Service
NWLQ is in business to do more than sell and buy computer network hardware. NWLQ strives to provide the best customer service to its worldwide client base. When a potential client contacts our facilities, they are assigned to one of our industry experienced Account Representatives. All of our Account Representatives have a minimum of 10 years experience in the IT field. NWLQ has Cisco certified technicians and professionals on staff to assist you in getting the right gear and to help from the RFQ process all the way through install. We are a full service hardware vendor! Call one of our account representatives at 1-800-998-9862 option 1 with any questions on our gear and service.

Quality Equipment
Every single unit of hardware that comes through NWLQ shipping dock is physically inspected and put through our thorough testing process by one of our Cisco or Extreme Networks certified engineers. Click here for more information on out testing process. All NWLQ gear comes with a standard 1 Year Replacement Warranty (end-user customers only)! Please inquire with your account representative for more details!

NWLQ has over $35 million in stock that can be shipped the same day if needed. NWLQ does offer payment and credit terms to qualified customers and ship worldwide on a daily basis. Whether you need Cisco, Extreme Networks, Compaq, F5, Foundry, or Nortel; you can expect the best service, fastest shipping, and quality gear in the industry - guaranteed! Give us a call and put us to the test!

We hope this definition of Accuracy was what you were looking for and appreciate your visit and welcome you back anytime.